Fixes#1099
We previously applied application keypad mode logic (`ESC=` or mode 66)
whenever it was active. However, from looking at the behavior of other
terminals (xterm and foot) it appears this isn't correct.
For xterm, application keypad mode only applies unconditionally if the
keyboard mode is VT220 (`-kt vt220`). For modern terminals, application
keypad mode is only applied if mode 1035 is disabled.
Mode 1035 is the "ignore numpad state with keypad mode" mode. It
defaults to true on terminal startup. If this is true, keypads are
always encoded in numerical mode. If this is false, the numlock state
will be respected.
Rather than immediately converting a color palette index into an RGB
value for a cell color, when a palette color is used track the palette
color directly in the cell state and convert to an RGB value in the
renderer.
This causes palette color changes to take effect immediately instead of
only for newly drawn cells.
Fixes#1183
I'm not sure why the original logic was there. When I translated the
original test cases to shell and ran them in xterm, they did NOT match
what Ghostty expected. This updates the tests to match xterm and removes
this case. We can add back in more tests if/when we figure out under
what scenario this original logic was correct (if it ever was).
Fixes#1159
The cursor position is an "active" coordinate (defined at the top of
Screen.zig), but our resize was treating it as a "viewport" coordinate.
This adds a new configuration `grapheme-width-method` to change the
default behavior that Ghostty uses to calculate grapheme width. The
default value is `unicode` which is identical to setting mode 2027.
**IMPORTANT:** This changes the default Ghostty behavior to be fully
grapheme-aware including ZWJs, VS15, VS16. This may cause issues with
some legacy programs and shells.
I've changed my mind that this should become the default because enough
people use emojis now that I've found in the beta program there are more
issues reported about "incorrect emoji width" than any possibly desync
issues. We'll see.
For legacy programs, this can still be set to `grapheme-width-method =
wcswidth`.
Only SGR, DECSCUSR, DECSTBM, and DECSLRM are handled, as these are the
only ones that Ghostty supports (as far as I can tell) and are the only
ones that seem actually useful.
This fixes a couple of subtle rectangle select behaviors:
* Corrects how selection rolls over when crossing the x-boundary; this
was mentioned in #1021, this properly corrects it so both sides of the
x-boundary do not share characters.
* Corrects a minor quirk in the selection of initial cells in a
selection - this can be more readily observed when selecting a single
line with rectangle select. To correct this, we only use the x axis
when calculating this instead of both x and y.
This fixes an issue where selections from the bottom-right to the
top-left (or top-left to bottom-right), in addition to some single-line
rectangle selections, were not working.
This works by handling situations where only one of the x or y
axes in the start or end points may need to be flipped to get the
correct top-left or bottom-right of a selection. We call these kinds of
orientations "mirrored", like you were looking in a mirror.
This also adds a small bit of logic that keeps these kinds of motions in
rectangle selection from selecting the character before or after it.
This has the current side-effect of anchoring a rectangle selection to
the original characters if you change directions during the selection,
something I will look at in a later commit.
Finally, this also removes rectangle select on double-click. I thought
this might be a good idea, but word select in rectangle mode really
does not work (the effect seems pretty erratic), and it's not
implemented in Kitty either.
Fixes#1008.
Implement handling of mode 1047, which enters the alternate screen. This
is not used often, typically applications will favor 1049 (enter alt
screen, save cursor, clear alt screen).
This adds rectangle select mode; when dragging with ctrl+alt (or
super+alt on MacOS), this allows you to select a rectangular region of
the terminal instead of the full start-end points of the buffer.
Fixes#906
This changes our resize behavior when increasing row height.
If the cursor was originally at the bottom of the viewport, existing
scrollback (if it exists) will be "pulled down" from the top,
effectively keeping the cursor at the bottom. This is the behavior
today, prior to this commit.
If the cursor is not at the bottom of the viewport, scrollback will NOT
be "pulled down" and instead blank lines will be added _below_. This is
new behavior.
Fixes#906
Previously, when the cursor isn't at the bottom and you resized to less
cols, the cursor would jump to the bottom of the viewport. But if you
resized to more columns it didn't do this. This was jarring. This commit
attempts to keep the cursor at the same place.
